the wire diagram is very small to read.
i have here pics
| Attachments: |
|
2016-05-06 01.02.12.jpg [ 142.83 KiB | Viewed 20070 times ] |
|
2016-05-06 01.00.11.jpg [ 143.97 KiB | Viewed 20070 times ] |
| Cordia Forum https://www.cordiapower.com/forum/ |
|
| SIVART's new toy https://www.cordiapower.com/forum/viewtopic.php?f=12&t=11961 |
Page 24 of 33 |
| Author: | Bitza [ 05 May 2016, 21:09 ] |
| Post subject: | Re: SIVART's new toy |
OK, I'll try and explain, The map sensor (also called pressure sensor) is located on the firewall to the right hand side of the igniter or E101. The yellow wire is the pressure sensor back to the ECU as part of the loom, if you cut this wire and bridge a fuel cut defender in its place you can raise the fuel cut limit. (AB's actually fuel cut at 14 psi so you can set it higher by lowering the FCD voltage) The FCD stops the sensor from reaching 5 volt and cutting the ignition at the E101, guys always say its a "fuel" cut but its not. See here for the wiring diagram. viewtopic.php?f=7&t=16157 |
|
| Author: | fernandothecarguy [ 06 May 2016, 02:55 ] | |||
| Post subject: | Re: SIVART's new toy | |||
the wire diagram is very small to read. i have here pics
|
||||
| Author: | S1VART [ 06 May 2016, 09:06 ] |
| Post subject: | Re: SIVART's new toy |
Ive always done it that way , I will try yours next time, the boost gauge used to cut out , but never registed errors though |
|
| Author: | fernandothecarguy [ 06 May 2016, 19:42 ] |
| Post subject: | Re: SIVART's new toy |
will this work? http://www.ebay.com/itm/DSP-Universal-F ... 2254692541 |
|
| Author: | Bitza [ 06 May 2016, 19:53 ] |
| Post subject: | Re: SIVART's new toy |
The picture only has three wires? You need four, positive, negative, and a colour to bridge the cut yellow wire. |
|
| Author: | fernandothecarguy [ 06 May 2016, 20:02 ] |
| Post subject: | Re: SIVART's new toy |
i see what you mean . i'll see if i can get one cheap some where ok i think i know how to install looks easy  http://www.turbosmartusa.com/wp-content ... 1/FCD2.pdf turbosmart seems the only one,anyone know of cheaper brand |
|
| Author: | Bitza [ 06 May 2016, 20:52 ] |
| Post subject: | Re: SIVART's new toy |
Pretty sure Jaycar still make them, can't buy them in stores anymore only over the net...........but you have to make it yourself.........not hard. Clips the voltage at 3.9 volt, perfect for the cordia, have made quite a few now, and at $20 it's cheap. http://www.jaycar.com.au/Kits,-Science- ... e/p/KC5439 |
|
| Author: | fernandothecarguy [ 07 May 2016, 01:05 ] |
| Post subject: | Re: SIVART's new toy |
man your the best thanks there out of Stock contacted them if there still making them will see what happens can't believe they sell Car Turbo Timer with Case and Independent Electronic Boost Controller Kit . |
|
| Author: | S1VART [ 16 May 2016, 15:25 ] |
| Post subject: | Re: SIVART's new toy |
here is my Sunday , Painting outside , with large winds ...lol  
|
|
| Author: | fernandothecarguy [ 16 May 2016, 20:19 ] |
| Post subject: | Re: SIVART's new toy |
looks good the old acrylic. hope paint don't peal off,when you pull masking from handles and molds |
|
| Author: | S1VART [ 17 May 2016, 13:06 ] |
| Post subject: | Re: SIVART's new toy |
all the black parts like the handles etc are plastic dip paint ...lol , trick too with taking the tape off , is do it while its slightly wet still and it never chips away, or trim with a stanley knife before I have to stick the moulds and badges on too, ( GLi badge ) I did the paint abit too smooth , so I roughed it up with random spraying , now to get the car dirty so it looks old |
|
| Author: | S1VART [ 27 Jun 2016, 10:36 ] |
| Post subject: | Re: SIVART's new toy |
got the evo out for the weekend, ended up at mt donna buang, 1 deg too 
|
|
| Author: | GORAN [ 27 Jun 2016, 13:17 ] |
| Post subject: | Re: SIVART's new toy |
Nice photo. |
|
| Author: | S1VART [ 28 Jun 2016, 09:10 ] |
| Post subject: | Re: SIVART's new toy |
thanks Goran, Im a leaner with the camera still but getting there |
|
| Author: | S1VART [ 25 Oct 2016, 11:56 ] |
| Post subject: | Re: SIVART's new toy |
some progress on the sleeper fixed, Rad support was cracked Fuel filter was held on by a cable tie wireS going between inlet and head ( massive air leak ) doing a different intercooler and piping ( cooler under the rad support ) new Grille dump pipe nuts loose still got to do, trim bonnet spider for the timing belt cover fit new dash pad ralliart rear end bushes fit bonnet locks gear shifter bushes + cable bushes replace fuel pump and re earth civic radiator and 14 inch fan needed, looking for a Front bar reo 
|
|
| Author: | S1VART [ 25 Oct 2016, 12:04 ] |
| Post subject: | Re: SIVART's new toy |
cooler fitment to suite the GL front bar  end look of fitment 
|
|
| Author: | S1VART [ 08 Dec 2016, 13:16 ] |
| Post subject: | Re: SIVART's new toy |
|
|
| Author: | Bitza [ 08 Dec 2016, 13:42 ] |
| Post subject: | Re: SIVART's new toy |
Your post is showing "photo not found"....WTF? |
|
| Author: | S1VART [ 08 Dec 2016, 13:45 ] |
| Post subject: | Re: SIVART's new toy |
really , I can see it though , I will check the settings |
|
| Author: | S1VART [ 08 Dec 2016, 14:56 ] |
| Post subject: | Re: SIVART's new toy |
I repatched the pic just incase bud |
|
| Page 24 of 33 | All times are UTC + 10 hours [ DST ] |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|