Cordia Forum https://www.cordiapower.com/forum/ |
|
Cordia head bolts https://www.cordiapower.com/forum/viewtopic.php?f=3&t=21193 |
Page 2 of 2 |
Author: | fernandothecarguy [ 05 Jul 2017, 18:53 ] |
Post subject: | Re: Cordia head bolts |
got more bad news. the mob i mention http://www.aagaskets.com.au/about.aspx there fudged made me do the run around in the end they only make the 2L gaskets don't waste your time. here is a reply to my email i sent them. Hi Fernando, Sorry to hear about your bad experience. The head gasket available is interchangeable between the 4g62 and 4g63. Usually a larger fire ring may lower engine compression but in this case it’s an insignificant amount and will not affect the application in a 4g62. Though it may seem large on the block the valve release on the head is actually larger than that of 82mm. We apologise for the inconvenience but hopefully that answers your questions. Kind Regards William Yue | Customer Services | AA Gaskets i would like to reply tell him to go f... him self when i rang him he said his gasket is exact 82mm fr |
Author: | fernandothecarguy [ 05 Jul 2017, 19:00 ] |
Post subject: | Re: Cordia head bolts |
i've also put up a post else where and someone has replied At first I thought that your engine might have been overbored. According to what I've read, the 4G62 engine has a bore of 80mm, not 82mm. However, 2mm converts to almost 79 thousandths of an inch, which is way too much for an overbore. I've read that Mitsubishi also sold some units from the 4G62 engine family to Hyundai. There was a version with an 81.6mm bore, (very close to your 82mm), known as the G4CN. Perhaps a previous owner dropped one of these engines into the car you have. If you have the larger bore G4CN, you might be able to find the correct gasket for it. |
Author: | Bitza [ 05 Jul 2017, 19:08 ] |
Post subject: | Re: Cordia head bolts |
The standard gasket is 82mm to allow for overbore........yes the standard piston is 80.6mm, better than 3mm on an 85mm gasket. You can see in my pic that the edge of the bore is slightly seen. |
Author: | fernandothecarguy [ 05 Jul 2017, 20:54 ] |
Post subject: | Re: Cordia head bolts |
hyundai has 83.5mm not sure if its ok found this one on ebay http://www.ebay.com.au/itm/Mitsubishi-C ... 1438.l2649 picture looks right. emailed guy yesterday still no response . rang him at lunch time they took my number but never called back. |
Author: | Bitza [ 07 Jul 2017, 19:48 ] |
Post subject: | Re: Cordia head bolts |
Where did you find this? |
Author: | Wexx [ 07 Jul 2017, 22:54 ] |
Post subject: | Re: Cordia head bolts |
Bitza wrote: Where did you find this? That is a decent looking gasket. Looks like it is coated AND has the molded rubber seal too. Info please. |
Author: | fernandothecarguy [ 08 Jul 2017, 10:16 ] |
Post subject: | Re: Cordia head bolts |
lots of searching ,emailing,ringing around. if i told where i got from you wouldn't believe me. managed to score 2 that's all they had old stock sitting on shelf for many years, rang around small country towns Mitsubishi spare parts. like Bathurst MITSUBISHI -Thomas Bros Mitsubishi wagga was lucky find |
Author: | 0-PSI [ 18 Jul 2017, 01:41 ] |
Post subject: | Re: Cordia head bolts |
Fernando if you ever consider selling your spare gasket, don't hesitate to contact me, I will buy it. |
Author: | fernandothecarguy [ 18 Jul 2017, 18:50 ] |
Post subject: | Re: Cordia head bolts |
well here's the deal i will swap gasket for fan it has to be in good running order and complete . |
Author: | 0-PSI [ 21 Jul 2017, 14:34 ] |
Post subject: | Re: Cordia head bolts |
I will check over the weekend to see if I have a spare fan among my parts & let you know. Otherwise if not, whatever the gasket owes you I will happily pay it. |
Author: | Wexx [ 21 Jul 2017, 23:26 ] |
Post subject: | Re: Cordia head bolts |
I'll dig out the fan as well and post pics this weekend. Been hot this week in middle Georgia. |
Author: | fernandothecarguy [ 22 Jul 2017, 09:05 ] |
Post subject: | Re: Cordia head bolts |
don't worry about I've already bought fan |
Author: | Wexx [ 22 Jul 2017, 09:31 ] |
Post subject: | Re: Cordia head bolts |
fernandothecarguy wrote: don't worry about I've already bought fan Cool beans. |
Author: | fernandothecarguy [ 23 Jul 2017, 23:27 ] | ||
Post subject: | Re: Cordia head bolts | ||
here something else i scored from same people i bought gasket.
|
Author: | TRQ-STR [ 04 Dec 2017, 00:05 ] |
Post subject: | Re: Cordia head bolts |
That's awesome!!! What are the chances you could scan to PDF and upload to the forum, haha? |
Page 2 of 2 | All times are UTC + 10 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |