Cordia Forum
https://www.cordiapower.com/forum/

Injector upgrade
https://www.cordiapower.com/forum/viewtopic.php?f=3&t=19357
Page 2 of 3

Author:  fernandothecarguy [ 30 Dec 2016, 21:38 ]
Post subject:  Re: Injector upgrade

came across this post if this helps
viewtopic.php?f=4&t=13992

Author:  Mong [ 01 Jan 2017, 22:01 ]
Post subject:  Re: Injector upgrade

Ill have a look for some photos champ.

Author:  fernandothecarguy [ 03 Jan 2017, 20:48 ]
Post subject:  Re: Injector upgrade

ok just wondering does anyone know size as in height/width & neck size as well as o'ring size and resistance of cordia injectors.
spoke to company that sells injectors and they will have the injectors for cordia ,just need exact
inf.
im not pulling my injectors out .
other thing can i used 900cc injectors with fuel cut defender ?

Author:  Bitza [ 03 Jan 2017, 20:58 ]
Post subject:  Re: Injector upgrade

As per specs:

Width: 10.89mm
O ring: 11.50 OD .....8.65mm ID
Neck length....12.70mm with rubber
Impedance.......02.6 OHMS

900cc njectors will still make the engine run rich.........best to use a rising rate adjustable regulator.........pretty hard to do on a cordia, will need to take into consideration the 90 psi fail safe of most fuel pumps!

Author:  fernandothecarguy [ 04 Jan 2017, 01:10 ]
Post subject:  Re: Injector upgrade

thanks mate will comeback with hopefully good news.

Author:  fernandothecarguy [ 04 Jan 2017, 22:44 ]
Post subject:  Re: Injector upgrade

got reply from injector people.
they asking for pic with all measurements.
so far i think i got all just need this

Attachments:
INJECTOR1.jpg
INJECTOR1.jpg [ 76.15 KiB | Viewed 20322 times ]

Author:  Bitza [ 07 Jan 2017, 16:02 ]
Post subject:  Re: Injector upgrade

Total height is: 65.53mm
Height of body is: 29.57mm

Author:  fernandothecarguy [ 07 Jan 2017, 18:29 ]
Post subject:  Re: Injector upgrade

thanks left message with seller.
also came across these.
http://www.ebay.com.au/itm/111948990497 ... EBIDX%3AIT

they look ok im just not sure of the plug angle.
i believe the neck is same size or maybe not LOL
im only guessing :lol:

Author:  fernandothecarguy [ 08 Jan 2017, 11:50 ]
Post subject:  Re: Injector upgrade

im told these will fit.
http://www.ebay.com.au/itm/321607349395?ul_noapp=true
the only problem is the plug angle.
i mentioned the fact there high impedance ,they say you can use high on low but
not the otherway

Author:  0-PSI [ 08 Jan 2017, 14:28 ]
Post subject:  Re: Injector upgrade

There is also these http://www.ebay.com/itm/Fuel-Injector-AIRTEX-4G1820-fits-84-86-Mitsubishi-Cordia-1-8L-L4-/122045770519?fits=Model%3ACordia&hash=item1c6a7eab17:g:IwcAAOSwAPlXiAcp&vxp=mtr though would turn into a very costly purchase.

Author:  fernandothecarguy [ 08 Jan 2017, 19:14 ]
Post subject:  Re: Injector upgrade

yes if you can afford over 500 dollars per injector.
the other thing they can't tell me if its for AB or Ac model injector.
they assume all models are the same.

Author:  fernandothecarguy [ 09 Jan 2017, 21:37 ]
Post subject:  Re: Injector upgrade

got the reply from injector people .

G'day Fernando!

Sorry for the delated reply.

We have 2 types I have in mind

One has a "neck" diameter of approx 10.40 - with a length of 16mm (or 11mm with buffer in place). overall length of injector 72mm

the other has a neck dia of 10.6 with a length of 11mm. Overall length of injector is 73mm

Both of the above use a 11.5mm dia o-ring

I hope this is helpful!

Kind regards

Steve

what you guys think?

Author:  Bitza [ 10 Jan 2017, 17:14 ]
Post subject:  Re: Injector upgrade

Sounds good, did you get any pics?

The injector top with the pressure regulator will require a 7mm spacer and longer bolts, are they still the bosch type plug?

The main spacing 12.7mm from the buffer might be a problem, as they come in at 11mm, can the buffer be shaved down to fit?

Thanks for the hard work, appreciated.

Author:  fernandothecarguy [ 10 Jan 2017, 19:18 ]
Post subject:  Re: Injector upgrade

this is the people i spoke to .
http://www.ebay.com.au/itm/111948990497?ul_noapp=true
the guy name is steve .

i know you said 800cc for my car just wondering what would happen
if i use 750cc ?
i bid on set of 4 injectors going cheap and i won :lol:
http://www.ebay.com.au/itm/4x-Siemens-7 ... true&rt=nc

never thought i would win so cheap :lol:
if its no good for what i need i might sell them get enough to buy 2x800cc or swap 4x750cc for 2 800cc

Author:  Bitza [ 10 Jan 2017, 20:13 ]
Post subject:  Re: Injector upgrade

If you use 750 (or unleaded injectors) in an AB you will have acceleration and boost problems, the engine will idle but not perform, not too mention the engine will run lean on boost as the ECU can't supply enough fuel as the AFM gives the ECU the digital signature.

Author:  fernandothecarguy [ 10 Jan 2017, 23:12 ]
Post subject:  Re: Injector upgrade

ok thanks i will try either swap or sale them

Author:  fernandothecarguy [ 10 Jan 2017, 23:41 ]
Post subject:  Re: Injector upgrade

Bitza wrote:
Sounds good, did you get any pics?

The injector top with the pressure regulator will require a 7mm spacer and longer bolts, are they still the bosch type plug?

The main spacing 12.7mm from the buffer might be a problem, as they come in at 11mm, can the buffer be shaved down to fit?

Thanks for the hard work, appreciated.


the guy gave me 2 choices

1-One has a "neck" diameter of approx 10.40 - with a length of 16mm (or 11mm with buffer in place). overall length of injector 72mm.

2-the other has a neck dia of 10.6 with a length of 11mm. Overall length of injector is 73mm

this are DENSO plugs are different ,they supply connectors for them
i might do a video of all the work hopefully i don't blow my self up

my question is wish one do i get?

Author:  Bitza [ 11 Jan 2017, 17:37 ]
Post subject:  Re: Injector upgrade

I would go the 72mm injector.

Author:  fernandothecarguy [ 12 Jan 2017, 13:11 ]
Post subject:  Re: Injector upgrade

Ok trying to get 2 injectors not
Sure my luck they only sell set of 4

Author:  fernandothecarguy [ 12 Jan 2017, 18:35 ]
Post subject:  Re: Injector upgrade

got me 2x 800cc 72mm injector. :D
cost 80 each including connectors and postage

Page 2 of 3 All times are UTC + 10 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/