Cordia Forum https://www.cordiapower.com/forum/ |
|
fuel cut defender install https://www.cordiapower.com/forum/viewtopic.php?f=3&t=21171 |
Page 3 of 3 |
Author: | Bitza [ 23 Apr 2017, 18:03 ] |
Post subject: | Re: fuel cut defender install |
Nice............going out for dinner anyway. |
Author: | fernandothecarguy [ 23 Apr 2017, 18:05 ] |
Post subject: | Re: fuel cut defender install |
enjoy |
Author: | sleeping giant [ 24 Apr 2017, 20:20 ] |
Post subject: | Re: fuel cut defender install |
Just for peace of mind , might be worth doing a compression check too if you have a tester mate, just to check for damage |
Author: | fernandothecarguy [ 24 Apr 2017, 23:27 ] |
Post subject: | Re: fuel cut defender install |
i did 120 psi all 4 cylinders . engine is clean no more over heating . im getting my original engine done by professional mechanic . resprayed his car so his going to return favor. |
Author: | fernandothecarguy [ 29 Apr 2017, 13:57 ] |
Post subject: | Re: fuel cut defender install |
hi guys had fcd wires checked. got meter on wire going to ecu. voltage varies on dial trying to find 3v! best to watch video. video coming soon |
Author: | Bitza [ 29 Apr 2017, 14:26 ] |
Post subject: | Re: fuel cut defender install |
HKS website says starion/cordia must be set to position two. |
Author: | fernandothecarguy [ 29 Apr 2017, 14:43 ] |
Post subject: | Re: fuel cut defender install |
https://youtu.be/yJI7LYO8s-w |
Author: | Bitza [ 29 Apr 2017, 16:06 ] |
Post subject: | Re: fuel cut defender install |
I may have not discussed the technical side of this device, setting 2 is correct at 1.2 volt, as the sensor is not under load (Boost) you have to take away the 1.2 volts from 5 volts, this will leave you with 3.8 volts once the sensor is under pressure, at this voltage the boost cut won't happen as the sensor can no longer see 5 volt. |
Author: | fernandothecarguy [ 29 Apr 2017, 19:23 ] |
Post subject: | Re: fuel cut defender install |
set it on 2 car drove good but was too much power wheels spinning etc. after few secs car started shaking spiting chips eventually stall. i didn't have metal clips on injectors one came out . put plugs back in started car running rough but got me home not sure if i caused damage |
Author: | Bitza [ 29 Apr 2017, 20:00 ] |
Post subject: | Re: fuel cut defender install |
What boost level did you run? |
Author: | fernandothecarguy [ 29 Apr 2017, 21:00 ] |
Post subject: | Re: fuel cut defender install |
got video coming soon. was on 18 psi so not sure why running rough so disconnected fcd . joined yellow factory wire back car running fine again. no damage |
Author: | Bitza [ 29 Apr 2017, 21:03 ] |
Post subject: | Re: fuel cut defender install |
Nice |
Author: | fernandothecarguy [ 29 Apr 2017, 23:04 ] |
Post subject: | Re: fuel cut defender install |
the car was very fast steering shacking, wheels spinning etc it was hard to film while driving it only took seconds . here is the video https://youtu.be/NigPw6RowYs |
Author: | fernandothecarguy [ 29 Apr 2017, 23:16 ] |
Post subject: | Re: fuel cut defender install |
next will be my new injectors gona boost 20 psi possibly will blow the head gasket this time. im trying to find copper gasket for new engine they cost way too much 400 bucs. anyone have one for sale? |
Author: | Bitza [ 29 Apr 2017, 23:47 ] |
Post subject: | Re: fuel cut defender install |
Look for an MLS head gasket.......cometic one will be good.........not too sure if they make them for the 62.......if they do use some copper spray to help seal the water jackets. Did the power increase take you by surprise? Can't see why the original boost gauge stayed all the way to the top! |
Author: | fernandothecarguy [ 30 Apr 2017, 01:42 ] |
Post subject: | Re: fuel cut defender install |
yes big power. i didn't expect it yes caught me by surprise. couldn't film as well as steering car. |
Page 3 of 3 | All times are UTC + 10 hours [ DST ] |
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |